Настройка встроенной сетевой карты

Автор: bdfy Дата: 26.06.2003 13:57 Привет всем !!
Есть сетевуха (интел чипсет e100) - проблема такая читаю мануал который прилагается к ней распаковываю архив .... делаю make install - все ок - потом как там написано insmod e100 - вот тут вылазит сообщение что неправильно сконфигурированы IRQ и I/O ...!!!
т е вроде как вручную их надо описать - при загрузке компа написано что 2 сетевых адаптера (который встроенный -котрый не работает) и внешний (который работает ) висят на прерываниях 10 и 11
пишу insmod e100 irq=11 - опять таже самая ошибка - чего я делаю не так а ? Подскажите pl !!
Re: настройка встроенной сетевой карты 26.06.2003 14:04Vladimir Dyakov вывод команды lspci дайте, пожалуйста, а также желательно содержимое файла /var/log/dmesg (как это вписывать в форму смотрите в хелпе: [community.asplinux.ru])
Re: настройка встроенной сетевой карты 26.06.2003 15:42bdfy
---
00:00.0 Host bridge: Intel Corp.: Unknown device 2560 (rev 03)
00:01.0 PCI bridge: Intel Corp.: Unknown device 2561 (rev 03)
00:1d.0 USB Controller: Intel Corp.: Unknown device 24c2 (rev 02)
00:1d.1 USB Controller: Intel Corp.: Unknown device 24c4 (rev 02)
00:1d.2 USB Controller: Intel Corp.: Unknown device 24c7 (rev 02)
00:1d.7 USB Controller: Intel Corp.: Unknown device 24cd (rev 02)
00:1e.0 PCI bridge: Intel Corp. 82801BA/CA PCI Bridge (rev 82)
00:1f.0 ISA bridge: Intel Corp.: Unknown device 24c0 (rev 02)
00:1f.1 IDE interface: Intel Corp.: Unknown device 24cb (rev 02)
00:1f.5 Multimedia audio controller: Intel Corp.: Unknown device 24c5 (rev 02)
01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX] (rev b2)
02:05.0 Ethernet controller: BROADCOM Corporation: Unknown device 4401 (rev 01)
02:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C (rev 10)

---
---
Linux version 2.4.18-5asp (leon@pylesos.asp-linux.com.ua) (gcc version 2.96 20000731 (ASPLinux 7.3 2.96-110)) #1 Sat Jul 6 20:16:12 EEST 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffec000 (usable)
BIOS-e820: 000000001ffec000 - 000000001ffef000 (ACPI data)
BIOS-e820: 000000001ffef000 - 000000001ffff000 (reserved)
BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
On node 0 totalpages: 131052
zone(0): 4096 pages.
zone(1): 126956 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=linux-2.4.18 ro root=302 hdc=ide-scsi
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 2539.150 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 5072.48 BogoMIPS
Memory: 513620k/524208k available (1124k kernel code, 10200k reserved, 790k data, 252k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: bfebfbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 12K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After vendor init, caps: bfebfbff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU: Intel(R) Pentium(R) 4 CPU 2.53GHz stepping 07
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf1e50, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router PIIX [8086/24c0] at 00:1f.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Diskquotas version dquot_6.5.0 initialized
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
block: 992 slots per queue, batch=248
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PCI_IDE: unknown IDE controller on PCI bus 00 device f9, VID=8086, DID=24cb
PCI: Device 00:1f.1 not available because of resource collisions
PCI_IDE: (ide_setup_pci_device:-) Could not enable device.
hda: Maxtor 6E040L0, ATA DISK drive
hdc: TEAC CD-W552E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 80293248 sectors (41110 MB-) w/2048KiB Cache, CHS=4998/255/63
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 470k freed
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 252k freed
Adding Swap: 1036152k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 20:37:41 Jul 6 2002
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 5 for device 00:1d.0
PCI: Sharing IRQ 5 with 01:00.0
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 9 for device 00:1d.1
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 9 for device 00:1d.2
PCI: Sharing IRQ 9 with 00:1f.1
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
PCI: Found IRQ 11 for device 00:1d.7
PCI: Sharing IRQ 11 with 02:0b.0
PCI: Setting latency timer of device 00:1d.7 to 64
hcd.c: ehci-hcd @ 00:1d.7, PCI device 8086:24cd (Intel Corp.)
hcd.c: irq 11, pci mem e08c8000
usb.c: new USB bus registered, assigned bus number 4
ehci-hcd.c: restricting 64bit DMA mappings to segment 0 ...
ehci-hcd.c: USB 2.0 support enabled, EHCI rev 1. 0
hub.c: USB hub found
hub.c: 6 ports detected
EXT3 FS 2.4-0.9.18, 14 May 2002 on ide0(3,2), internal journal
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: TEAC Model: CD-W552E Rev: 1.05
Type: CD-ROM ANSI SCSI revision: 02

---
Прерывание надо ставить 10 -в бисое так показывается а вот Io ?
как его получить ?
Re: настройка встроенной сетевой карты 26.06.2003 16:05Vladimir Dyakov 1) На 11 прерывании у вас, судя по всему сидит Realtek Semiconductor Co., Ltd. RTL-8139/8139C. Попробуйте 10 прерывание. Попробуйте io=c000
2) Попробуйте в биосе поиграть с параметрами, в т.ч. plug'n'play OS installed / not installed, такое ощущение, что проблема в биосе.
Re: настройка встроенной сетевой карты 27.06.2003 15:28Vladimir Dyakov по ходу дела, в 2.4.22pre2 есть изменения с модулем eepro100: [kernel.org]
RSS-материал